Crest Automotive Tuning - C) CHASSIS, BRAKES, SUSPENSION & STEERING UPGRADES

Product Code: bmwmounthalf

Click to Enlarge

E36/E46 COUPE & Z4 STREET REAR SHOCK MOUNTS (PAIR) HALF PLATE

Using urethane bushings that can be installed in either a stiff or semi-stiff position, this is the perfect rear shock mount for BMW E36, E46 and Z4 cars.

Will not fit E36/E46 Coupes or Sedans

Made of 6061 aircraft aluminum, these mounts are a perfect fit for any shock.
Two steel studs mounted to a steel bracket sandwich this mount to the body, and allow quick access from under the wheelwell for adjusting rear shocks, especially Konis.
This part, including the urethane bushings, has a lifetime guarantee to the original purchaser. Price is per pair.

available for 10mm, 12mm, 14mm shock absorber shaft.

Estimated Volumetric Shipping Weight : 3.00 Kg

Product Code: bmwmountrace

Click to Enlarge

REF: BMWMOUNTRACE

Rear shock mount to fit BMW, only recommended for race cars.

If you are racing, and especially with coil-over shocks, you need this monoball rear mount that slides for spring to tire clearance.

Complete with shock stem adapters.Uses a spherical bearing instead of urethane or rubber. Please specify 10, 12, 14 or 16mm stem diameter.

Billet aluminum with spherical bearings.

Note that ALL Ground Control rear shock mounts are clamped to the body for extra strength. Price per pair.

Estimated Volumetric Shipping Weight : 3.00 Kg

Product Code: m3bearing

Click to Enlarge

E30, 92-95 E36 & M3, LOWER CONTROL ARM BUSHINGS (BMWCCA LEGAL)

Ref: M3BEARING95

Only rotates in 2 axes to satisfy prepared class rules of BMWCCA and SCCA SOL2 street prepared class.

• Replaces your soft, or torn, control arm bushings with offset(M3) aluminum bearing retainer self-lubricating 3M stock.
• Reduces control arm deflection for a more precise steering feel.
• 3M bushing can be easily replaced if needed.
• Retainer and hardware are anodized or zinc plated for corrosion resistance.

E30 M3 geometry; use ONLY with E30, E30 M3, or 92-95 E36 & M3 control arms. For 96-99 M3, use m3bearing96.

Please specify which vehicle and model when ordering.

Estimated Volumetric Shipping Weight : 3.00 Kg

Product Code: gcrollcon-1

Click to Enlarge

REF: BMWROLLCONTROL

This E36/Z3 Roll Center Adjusters replace the factory front lower ball joints, including Adjustable tie rods.

These new bushings assist in correcting the vehicles roll center after lowering. They are adjustable depending on your vehicles final ride height.

In conjunction with the Ground Control Racing Tierods / Bump Steer Adjusters also included you can achieve proper suspension alignment, as these allow the bumpsteer to be adjusted by moving the tie rods up and down with spacers.This is similar to the pieces used by BMW factory racing teams and they recommend that the rod ends be inspected every session, and replaced if necessary.

The GC kit comes with Aurora aircraft grade rod ends and all spacers.

Estimated Volumetric Shipping Weight : 10.00 Kg

Product Code: gcspanner

Click to Enlarge

Ref: GCSpanner

This is a replacement spanner for Ground Control coilover kits.

This spanner is included only in certain GC coilover kits, so if your GC coilover kit included a spanner, then you do not need to buy this.

The most common misconception why people think they may need a spanner, is that they are tilting the car on its side to adjust the collars, so they are fighting the swaybars. The swaybars are designed to keep the car from tilting by pushing against the suspension, which makes it difficult to turn the adjuster by hand.

A spanner could easily ruin things if used under these conditions.

If this describes your situation, try lifting the front or rear of the car off the ground, and adjust with your hands.

Estimated Volumetric Shipping Weight : 2.00 Kg